DSTV Extra Channels

[francoisvv77]

A while back someone told me that he was watching the Hillsong conference on DSTV, but on additional channels that he enabled. When I asked him how he did it, he told me that there was a few things that you needed to do in order to get access to the channels. I remember a while back (before I had DSTV...) i read in a thread where someone explained how to do it, but I can't seem to find the thread. Can anyone plz help me with this?

Thank you so much!!!

 

[upup]

http://www.god.tv/tunein

The GOD Channel's free-to-air signal is available via satellite throughout Africa enabling television viewers to experience anointed Christian programming completely free of charge.

The GOD Channel's dedicated Africa feed is broadcast 24-hours-a-day on two major satellites - Thaicom 3 across the continent of Africa and PAS 7 in Southern Africa which means that every TV owner in Africa, who has a dish and decoder, is able to watch the Channel. It also means that the GOD Channel signal can be easily pulled down and re-distributed via terrestrial transmitters to viewers in the most remote areas, who can pick up the Channel without a satellite decoder.

To watch the GOD Channel on your current decoder, just follow these steps for your type of decoder:

Multichoice Decoder: Single & PVR

* Press menu on remote
* Advanced options-OK
* Dish installations-OK
* Enter PIN code: 9949
* (7) Reset to factory defaults – OK - OK
* When done scanning
* Press menu on remote
* Advanced options-OK
* Dish installations-OK
* 9949
* Go to Network 2 then press the right arrow button until you see the word “other”
* DO NOT PRESS OK
* Scroll down to (6) Scan All Networks – OK-OK
* When done scanning

To watch the GOD Channel:

* On your remote control, press TV button
* Press the ‘Up Arrow” button on your remote
* Find and select PUBLIC PAS 7/10 and press OK
* Press the P- button on your remote until you find the GOD CHANNEL


Multichoice Decoder: Old PVR & (+- 5 yrs)

* On your REMOTE CONTROL Press the MENU button
* Press 6 for ADVANCED OPTIONS
* Press 1 for DISH INSTALLATIONS
* Enter PIN code: 9949
* Press 1 for LNB CONFIGURAGTON and press OK
* Press 2 for LNB 2 SETUP (Option A, Position B) and press OK
* Press 1 for LNB. It should be “DISABLED. Press OK
* Press the left arrow button once, ‘DISABLED’ should now change to ‘ENABLED’. Press OK
* Go to Option 8, ACCEPT THESE SETTINGS and Press OK
* Press EXIT once
* Press 2 for NETWORK CONFIGURATION
* Press 2 for NETWORK 2 SETUP. (If 2 is grayed out, use NETWORK 3 SETUP)
* On SIGNAL SETUP press the OK to highlight DISABLED
* Press ‘Right arrow’ (>) to change to ENABLED and press OK
* Make sure #2 ‘ORBITAL POSITION’ is PAS 7/10
* Make sure #3 ‘USE NIT’ is YES
* Press 4 for FREQUENCY: (You may need to press OK Before the next step)
* Press ‘Left arrow button (<) 5 times
* Enter 11170 and press OK to save
* Press 5 for SYMBOL RATE: (you may need to press OK before the next step)
* Press the ‘left arrow’ button (<) 5 times
* Enter 26652 & OK to save
* Make sure #6 POLARIZATION’ is VERTICAL
* Press 7 for FEC (you may need to press OK before the next step)
* Press left arrow button (<) 3 tunes until it reads 5/6
* Press OK button to save
* Press 8 to VIEW SIGNAL STRENGTH then press OK button to save
* When saved press EXIT — once only!
* Press 4 to SCAN ALL NETWORKS
* After Scanning process is complete, receiver may go to channel 100 or to another DSTV channel


To watch the GOD Channel:

* On your remote control, press TV button
* Press the ‘Up Arrow” button on your remote
* Find and select PUBLIC PAS 7/10 and press OK
* Press the P- button on your remote until you find the GOD CHANNEL


Please note: No free to air channels are available on the new HD PVR

hope this works well.

http://www.spiritword.org/
this site under construction currently.

 

[Madhawk]

Thank you for those instructions.

I followed your instructions this evening and I got it to work.

It's on Channel 39.