It just died :(

C

charlie_82

Expert Member
Joined
Dec 11, 2007
Messages
2,993
Reaction score
1
Location
Johannesburg
After many years of loyal service, my backup 80gb drive just keeled over...
No power, no spinning. There was no power surge, no clicking, nothing - it just died.

Problem is I have all my photographs (amoung other data of course) on this drive.
Anyone got any suggestions on data recovery?
 
It's an internal 3.5" SATA and is my backup drive.
Mostly just for photo's, music, movies etc. I used it more as a temporary storage since most of my stuff is on discs. Just left whatever I was too lazy to burn on there
 
charlie_82 said:
After many years of loyal service, my backup 80gb drive just keeled over...
No power, no spinning. There was no power surge, no clicking, nothing - it just died.

Problem is I have all my photographs (amoung other data of course) on this drive.
Anyone got any suggestions on data recovery?
Click to expand...

burial service is at 3pm ?
 
moggie said:
tried a different power source and/or sata cable?
Click to expand...

Yeah tried that. Tried different machines as well. BIOS won't pick it up, nor will Windows. To be expected seeing as how the drive doesn't seem to be spinning or have any power.

Read about freezing it for a few hours, which I think I'll try. Also read about switching out the logical boards but will need another identical drive to make that happen so that'll be quite tough.

Don't really wanna fork out thousands on data recovery but would like to have my photo's back at least - it's the only thing on the drive that can't be replaced :(
 
Can you post the drive make, model and other figures on the sticker - maybe someone has a spare where you can use the logical board to get your data off.
 
Try tap it. If the disk is not spinning it could be that the bearing is seized (or seizing). Gently tap the drive in the centre of the spindle with your knuckle, as if you were knocking on a door. If the disk starts spinning, immediately copy all your stuff off and junk-it. I have recovered many disks this way....
 
Conradl said:
Try tap it. If the disk is not spinning it could be that the bearing is seized (or seizing). Gently tap the drive in the centre of the spindle with your knuckle, as if you were knocking on a door. If the disk starts spinning, immediately copy all your stuff off and junk-it. I have recovered many disks this way....
Click to expand...
Yeah tried shaking it when it was unplugged. Will try the tapping thing - I assume this is when it's plugged in and the machine is on?

howardb said:
Can you post the drive make, model and other figures on the sticker - maybe someone has a spare where you can use the logical board to get your data off.
Click to expand...
Cool...

Make: Seagate Barracuda 7200.7 (80GB)
Model: ST380817AS
S/N: 5MR0S27A
P/N: 9W3932-370
HDA P/N: 100334813
Config: C4R-03
Firmware: 3.42
 
wrap it in plastic and put in the fridge for an hour. Then plug it in and try turning it on.
 
Garyvdh said:
wrap it in plastic and put in the fridge for an hour. Then plug it in and try turning it on.
Click to expand...

Yeah read about that one. Will give it a bash when I get home today.
I'm hoping it's not a big problem. My PC has been dormant for a few weeks - drive worked fine before that
 
charlie_82 said:
Yeah tried shaking it when it was unplugged. Will try the tapping thing - I assume this is when it's plugged in and the machine is on?


Cool...

Make: Seagate Barracuda 7200.7 (80GB)
Model: ST380817AS
S/N: 5MR0S27A
P/N: 9W3932-370
HDA P/N: 100334813
Config: C4R-03
Firmware: 3.42
Click to expand...

Yes, you have to do it when the machine is on and ready to copy your data. Before you freeze the drive, which should be last resort after you have accepted that your data is gone, try to first determine the problem.

Try this: Unplug the power cable (keep the SATA cable in) from the disk and boot your machine, the POST should run through quickly when detecting the disk drives (as the disk is not powered). Then plug the power back in and boot again. If the machine boots at the same speed, then the disk is not getting power, and there may be a problem with the board.

If the machine takes a long time to boot, i.e. it hangs when detecting disks, then the disk is powered and detected; but the POST is waiting for the disk to spin up, until it finally times out.

In the first instance you would need to replace the board, in the second tapping the disk gently could make it spin.
 
Conradl said:
Yes, you have to do it when the machine is on and ready to copy your data. Before you freeze the drive, which should be last resort after you have accepted that your data is gone, try to first determine the problem.

Try this: Unplug the power cable (keep the SATA cable in) from the disk and boot your machine, the POST should run through quickly when detecting the disk drives (as the disk is not powered). Then plug the power back in and boot again. If the machine boots at the same speed, then the disk is not getting power, and there may be a problem with the board.

If the machine takes a long time to boot, i.e. it hangs when detecting disks, then the disk is powered and detected; but the POST is waiting for the disk to spin up, until it finally times out.

In the first instance you would need to replace the board, in the second tapping the disk gently could make it spin.
Click to expand...

I'm pretty sure it's not the motherboard cos I've tried it in two machines. Will try the tapping thing in a few minutes
 
charlie_82 said:
Crap that didn't work
Click to expand...

Board = Circuit board on the disk, not motherboard ;)

If you set the BIOS to disk autodetect, does it hang there for a while when you boot, or just flash past quickly? If you put your ear to the disk, right on it, do you hear anything?
 
Conradl said:
Board = Circuit board on the disk, not motherboard ;)

If you set the BIOS to disk autodetect, does it hang there for a while when you boot, or just flash past quickly? If you put your ear to the disk, right on it, do you hear anything?
Click to expand...

Ah ok lol
It seems to go by quickly, not picking anything up. I can't imagine it would cos it's really not spinning. I don't think there's any power going through but could just be that it's not spinning. I'm not even sure if this hard drive have a power LED or not
 
It sounds like there is no power then, i.e. the circuit board is broken. Does the bottom of the drive smell/look/taste burnt?
 
You must log in or register to reply here.
Back
Top
Sign up to the MyBroadband newsletter
X