Linux - HOWTO (With Stats)

Status
Not open for further replies.
Hi raistlin,

I am assume you have another serial port in the notebook, since I see it complaining about keys pressed. In /etc/wvdial.conf, increase the novatel serial port (currently /dev/ttyS0 to /dev/ttyS1 to /dev/ttyS2) until you find a working one. I can't seem to find where the card is detected in your messages.

Laterz !

raistlin said:
Hello

Well i'm starting with linux :D

trying to install my Novatel Meril U740 on Ubuntu 6.06 with no sucess :(
btw sorry for messages in portuguese :) but i installed the portuguese version :D
I followed the Tazz_Tux steps but when i run

wvdial novatel internet 3gonly 384k

--> WvDial: Internet dialer version 1.55
--> Cannot open /dev/ttyS0: Input/output error
--> Cannot open /dev/ttyS0: Input/output error
--> Cannot open /dev/ttyS0: Input/output error


this is what i get with the tail -f /var/log/messages

Code: 
Sep 18 17:52:28 localhost kernel: [17181241.592000] atkbd.c: Use 'setkeycodes e033 <keycode>' to make it known.
Sep 18 17:55:08 localhost kernel: [17181401.888000] psmouse.c: TouchPad at isa0060/serio4/input0 - driver resynched.
Sep 18 18:00:00 localhost gconfd (root-7348): a iniciar (versão 2.14.0), pid 7348 utilizador 'root'
Sep 18 18:00:00 localhost gconfd (root-7348): Resolvido o endereço "xml:readonly:/etc/gconf/gconf.xml.mandatory" para uma fonte de configuração apenas de leitura na posição 0
Sep 18 18:00:00 localhost gconfd (root-7348): Resolvido o endereço "xml:readwrite:/root/.gconf" para uma fonte de configuração com permissão de escrita na posição 1
Sep 18 18:00:00 localhost gconfd (root-7348): Resolvido o endereço "xml:readonly:/etc/gconf/gconf.xml.defaults" para uma fonte de configuração apenas de leitura na posição 2
Sep 18 18:00:00 localhost gconfd (root-7348): Resolvido o endereço "xml:readonly:/var/lib/gconf/debian.defaults" para uma fonte de configuração apenas de leitura na posição 3
Sep 18 18:00:00 localhost gconfd (root-7348): Resolvido o endereço "xml:readonly:/var/lib/gconf/defaults" para uma fonte de configuração apenas de leitura na posição 4
Sep 18 18:01:00 localhost gconfd (root-7348): Servidor GConf não está a ser utilizado, a terminar.
Sep 18 18:01:00 localhost gconfd (root-7348): A terminar
Sep 18 18:08:26 localhost kernel: [17182200.024000] atkbd.c: Unknown key pressed (translated set 2, code 0xb4 on isa0060/serio0).
Sep 18 18:08:26 localhost kernel: [17182200.024000] atkbd.c: Use 'setkeycodes e034 <keycode>' to make it known.
Sep 18 18:08:26 localhost kernel: [17182200.064000] atkbd.c: Unknown key released (translated set 2, code 0xb4 on isa0060/serio0).
Sep 18 18:08:26 localhost kernel: [17182200.064000] atkbd.c: Use 'setkeycodes e034 <keycode>' to make it known.
Sep 18 18:08:27 localhost kernel: [17182200.892000] atkbd.c: Unknown key pressed (translated set 2, code 0xb4 on isa0060/serio0).
Sep 18 18:08:27 localhost kernel: [17182200.892000] atkbd.c: Use 'setkeycodes e034 <keycode>' to make it known.
Sep 18 18:08:27 localhost kernel: [17182200.988000] atkbd.c: Unknown key released (translated set 2, code 0xb4 on isa0060/serio0).
Sep 18 18:08:27 localhost kernel: [17182200.988000] atkbd.c: Use 'setkeycodes e034 <keycode>' to make it known.
Sep 18 18:08:28 localhost kernel: [17182201.380000] atkbd.c: Unknown key released (translated set 2, code 0xe0 on isa0060/serio0).
Sep 18 18:08:28 localhost kernel: [17182201.380000] atkbd.c: Use 'setkeycodes e060 <keycode>' to make it known.
Sep 18 18:08:28 localhost kernel: [17182201.480000] atkbd.c: Unknown key released (translated set 2, code 0xb4 on isa0060/serio0).
Sep 18 18:08:28 localhost kernel: [17182201.480000] atkbd.c: Use 'setkeycodes e034 <keycode>' to make it known.
Sep 18 18:08:32 localhost gconfd (root-7670): a iniciar (versão 2.14.0), pid 7670 utilizador 'root'
Sep 18 18:08:32 localhost gconfd (root-7670): Resolvido o endereço "xml:readonly:/etc/gconf/gconf.xml.mandatory" para uma fonte de configuração apenas de leitura na posição 0
Sep 18 18:08:32 localhost gconfd (root-7670): Resolvido o endereço "xml:readwrite:/root/.gconf" para uma fonte de configuração com permissão de escrita na posição 1
Sep 18 18:08:32 localhost gconfd (root-7670): Resolvido o endereço "xml:readonly:/etc/gconf/gconf.xml.defaults" para uma fonte de configuração apenas de leitura na posição 2
Sep 18 18:08:32 localhost gconfd (root-7670): Resolvido o endereço "xml:readonly:/var/lib/gconf/debian.defaults" para uma fonte de configuração apenas de leitura na posição 3
Sep 18 18:08:32 localhost gconfd (root-7670): Resolvido o endereço "xml:readonly:/var/lib/gconf/defaults" para uma fonte de configuração apenas de leitura na posição 4
Sep 18 18:09:02 localhost gconfd (root-7670): Servidor GConf não está a ser utilizado, a terminar.
Sep 18 18:09:02 localhost gconfd (root-7670): A terminar

The modprobe usbserial vendor=0x1410 product=0x1410 or modprobe usbserial vendor=0x1410 product=0x1400 don't do anything

With the lsusb command i have this

Code: 
Bus 004 Device 006: ID 1410:1410
Bus 004 Device 001: ID 0000:0000
Bus 005 Device 001: ID 0000:0000
Bus 003 Device 001: ID 0000:0000
Bus 001 Device 003: ID 1267:0210 Logic3 / SpectraVideo plc
Bus 001 Device 001: ID 0000:0000
Bus 002 Device 001: ID 0000:0000


I really need some help on this plzzzzzzzzz
regards
Click to expand...
 
hya

Well i tried till ttyS10 all gave me input/output error except ttyS1 that gave me

--> Cannot open /dev/ttyS1: No such device
--> Cannot open /dev/ttyS1: No such device
--> Cannot open /dev/ttyS1: No such device


Another thing ... whats the meaning of "I see it complaining about keys pressed"
 
Hmmmm

I removed the pcmcia card while running tail -f /var/log/messages and heres what i got

Code: 
Sep 19 04:48:25 localhost gconfd (root-5279): Resolvido o endereço "xml:readonly :/var/lib/gconf/debian.defaults" para uma fonte de configuração apenas de leitur a na posição 3
Sep 19 04:48:25 localhost gconfd (root-5279): Resolvido o endereço "xml:readonly :/var/lib/gconf/defaults" para uma fonte de configuração apenas de leitura na po sição 4
Sep 19 04:49:10 localhost kernel: [17179833.508000] ttyS1: LSR safety check enga ged!
Sep 19 04:49:10 localhost last message repeated 2 times
Sep 19 04:50:18 localhost kernel: [17179901.540000] ttyS1: LSR safety check enga ged!
Sep 19 04:50:18 localhost last message repeated 2 times
Sep 19 04:50:25 localhost gconfd (root-5279): Servidor GConf não está a ser util izado, a terminar.
Sep 19 04:50:25 localhost gconfd (root-5279): A terminar
Sep 19 04:52:00 localhost exiting on signal 15
Sep 19 04:52:01 localhost syslogd 1.4.1#17ubuntu7: restart.
Sep 19 04:54:25 localhost kernel: [17180149.388000] usb 4-1: USB disconnect, address 6
Sep 19 04:54:25 localhost kernel: [17180149.388000] pccard: card ejected from slot 0
Sep 19 04:54:26 localhost kernel: [17180149.424000] ohci_hcd 0000:07:00.0: remove, state 0
Sep 19 04:54:26 localhost kernel: [17180149.424000] usb usb4: USB disconnect, address 1
Sep 19 04:54:26 localhost kernel: [17180149.424000] ohci_hcd 0000:07:00.0: USB bus 4 deregistered
Sep 19 04:54:26 localhost kernel: [17180149.424000] ACPI: PCI interrupt for device 0000:07:00.0 disabled
Sep 19 04:54:26 localhost kernel: [17180149.424000] ohci_hcd 0000:07:00.1: remove, state 0
Sep 19 04:54:26 localhost kernel: [17180149.424000] usb usb5: USB disconnect, address 1
Sep 19 04:54:26 localhost kernel: [17180149.424000] ohci_hcd 0000:07:00.1: USB bus 5 deregistered
Sep 19 04:54:26 localhost kernel: [17180149.428000] ACPI: PCI interrupt for device 0000:07:00.1 disabled
Sep 19 04:54:46 localhost kernel: [17180169.804000] pccard: CardBus card inserted into slot 0
Sep 19 04:54:46 localhost kernel: [17180169.804000] PCI: Enabling device 0000:07:00.0 (0000 -> 0002)
Sep 19 04:54:46 localhost kernel: [17180169.804000] ACPI: PCI Interrupt 0000:07:00.0[A] -> GSI 20 (level, low) -> IR Q 185
Sep 19 04:54:46 localhost kernel: [17180169.804000] ohci_hcd 0000:07:00.0: OHCI Host Controller
Sep 19 04:54:46 localhost kernel: [17180169.804000] ohci_hcd 0000:07:00.0: new USB bus registered, assigned bus numb er 4
Sep 19 04:54:46 localhost kernel: [17180169.804000] ohci_hcd 0000:07:00.0: irq 185, io mem 0x54000000
Sep 19 04:54:46 localhost kernel: [17180169.888000] hub 4-0:1.0: USB hub found
Sep 19 04:54:46 localhost kernel: [17180169.888000] hub 4-0:1.0: 3 ports detected
Sep 19 04:54:46 localhost kernel: [17180169.992000] PCI: Enabling device 0000:07:00.1 (0000 -> 0002)
Sep 19 04:54:46 localhost kernel: [17180169.992000] ACPI: PCI Interrupt 0000:07:00.1[B] -> GSI 20 (level, low) -> IR Q 185
Sep 19 04:54:46 localhost kernel: [17180169.992000] ohci_hcd 0000:07:00.1: OHCI Host Controller
Sep 19 04:54:46 localhost kernel: [17180169.992000] ohci_hcd 0000:07:00.1: new USB bus registered, assigned bus numb er 5
Sep 19 04:54:46 localhost kernel: [17180169.992000] ohci_hcd 0000:07:00.1: irq 185, io mem 0x54001000
Sep 19 04:54:46 localhost kernel: [17180170.100000] hub 5-0:1.0: USB hub found
Sep 19 04:54:46 localhost kernel: [17180170.100000] hub 5-0:1.0: 2 ports detected
Sep 19 04:54:46 localhost kernel: [17180170.296000] usb 4-1: new full speed USB device using ohci_hcd and address 2
Sep 19 04:54:47 localhost kernel: [17180171.040000] usb 4-1: new full speed USB device using ohci_hcd and address 3
Sep 19 04:54:48 localhost kernel: [17180171.792000] usb 4-1: new full speed USB device using ohci_hcd and address 4
Sep 19 04:54:52 localhost kernel: [17180175.588000] usb 4-1: new full speed USB device using ohci_hcd and address 6
 
Hi raistlin,

run that tail command and then in a second console restart pcmcia (normally /etc/init.d/pcmcia restart)

As for the keypressed thing:

Sep 18 18:08:26 localhost kernel: [17182200.024000] atkbd.c: Unknown key pressed (translated set 2, code 0xb4 on isa0060/serio0).

That is what I was talking about - that appears to be serial0 aka /dev/ttyS0

:)

raistlin said:
hya

Well i tried till ttyS10 all gave me input/output error except ttyS1 that gave me

--> Cannot open /dev/ttyS1: No such device
--> Cannot open /dev/ttyS1: No such device
--> Cannot open /dev/ttyS1: No such device


Another thing ... whats the meaning of "I see it complaining about keys pressed"
Click to expand...
 
Ok - that was stupid of me ! I mis-read the model number.

Run this (with the card in - and the tail running)

modprobe usbserial vendor=0x1410 product=0x1410

You will see it register the comm ports. It should be /dev/tty/USB/0 or something like that. Take the first one and change the config to that. That should work :)

raistlin said:
Hmmmm

I removed the pcmcia card while running tail -f /var/log/messages and heres what i got

Code: 
Sep 19 04:48:25 localhost gconfd (root-5279): Resolvido o endereço "xml:readonly :/var/lib/gconf/debian.defaults" para uma fonte de configuração apenas de leitur a na posição 3
Sep 19 04:48:25 localhost gconfd (root-5279): Resolvido o endereço "xml:readonly :/var/lib/gconf/defaults" para uma fonte de configuração apenas de leitura na po sição 4
Sep 19 04:49:10 localhost kernel: [17179833.508000] ttyS1: LSR safety check enga ged!
Sep 19 04:49:10 localhost last message repeated 2 times
Sep 19 04:50:18 localhost kernel: [17179901.540000] ttyS1: LSR safety check enga ged!
Sep 19 04:50:18 localhost last message repeated 2 times
Sep 19 04:50:25 localhost gconfd (root-5279): Servidor GConf não está a ser util izado, a terminar.
Sep 19 04:50:25 localhost gconfd (root-5279): A terminar
Sep 19 04:52:00 localhost exiting on signal 15
Sep 19 04:52:01 localhost syslogd 1.4.1#17ubuntu7: restart.
Sep 19 04:54:25 localhost kernel: [17180149.388000] usb 4-1: USB disconnect, address 6
Sep 19 04:54:25 localhost kernel: [17180149.388000] pccard: card ejected from slot 0
Sep 19 04:54:26 localhost kernel: [17180149.424000] ohci_hcd 0000:07:00.0: remove, state 0
Sep 19 04:54:26 localhost kernel: [17180149.424000] usb usb4: USB disconnect, address 1
Sep 19 04:54:26 localhost kernel: [17180149.424000] ohci_hcd 0000:07:00.0: USB bus 4 deregistered
Sep 19 04:54:26 localhost kernel: [17180149.424000] ACPI: PCI interrupt for device 0000:07:00.0 disabled
Sep 19 04:54:26 localhost kernel: [17180149.424000] ohci_hcd 0000:07:00.1: remove, state 0
Sep 19 04:54:26 localhost kernel: [17180149.424000] usb usb5: USB disconnect, address 1
Sep 19 04:54:26 localhost kernel: [17180149.424000] ohci_hcd 0000:07:00.1: USB bus 5 deregistered
Sep 19 04:54:26 localhost kernel: [17180149.428000] ACPI: PCI interrupt for device 0000:07:00.1 disabled
Sep 19 04:54:46 localhost kernel: [17180169.804000] pccard: CardBus card inserted into slot 0
Sep 19 04:54:46 localhost kernel: [17180169.804000] PCI: Enabling device 0000:07:00.0 (0000 -> 0002)
Sep 19 04:54:46 localhost kernel: [17180169.804000] ACPI: PCI Interrupt 0000:07:00.0[A] -> GSI 20 (level, low) -> IR Q 185
Sep 19 04:54:46 localhost kernel: [17180169.804000] ohci_hcd 0000:07:00.0: OHCI Host Controller
Sep 19 04:54:46 localhost kernel: [17180169.804000] ohci_hcd 0000:07:00.0: new USB bus registered, assigned bus numb er 4
Sep 19 04:54:46 localhost kernel: [17180169.804000] ohci_hcd 0000:07:00.0: irq 185, io mem 0x54000000
Sep 19 04:54:46 localhost kernel: [17180169.888000] hub 4-0:1.0: USB hub found
Sep 19 04:54:46 localhost kernel: [17180169.888000] hub 4-0:1.0: 3 ports detected
Sep 19 04:54:46 localhost kernel: [17180169.992000] PCI: Enabling device 0000:07:00.1 (0000 -> 0002)
Sep 19 04:54:46 localhost kernel: [17180169.992000] ACPI: PCI Interrupt 0000:07:00.1[B] -> GSI 20 (level, low) -> IR Q 185
Sep 19 04:54:46 localhost kernel: [17180169.992000] ohci_hcd 0000:07:00.1: OHCI Host Controller
Sep 19 04:54:46 localhost kernel: [17180169.992000] ohci_hcd 0000:07:00.1: new USB bus registered, assigned bus numb er 5
Sep 19 04:54:46 localhost kernel: [17180169.992000] ohci_hcd 0000:07:00.1: irq 185, io mem 0x54001000
Sep 19 04:54:46 localhost kernel: [17180170.100000] hub 5-0:1.0: USB hub found
Sep 19 04:54:46 localhost kernel: [17180170.100000] hub 5-0:1.0: 2 ports detected
Sep 19 04:54:46 localhost kernel: [17180170.296000] usb 4-1: new full speed USB device using ohci_hcd and address 2
Sep 19 04:54:47 localhost kernel: [17180171.040000] usb 4-1: new full speed USB device using ohci_hcd and address 3
Sep 19 04:54:48 localhost kernel: [17180171.792000] usb 4-1: new full speed USB device using ohci_hcd and address 4
Sep 19 04:54:52 localhost kernel: [17180175.588000] usb 4-1: new full speed USB device using ohci_hcd and address 6
Click to expand...
 
Ok the modprobe gave me

Sep 19 05:01:23 localhost kernel: [17180566.528000] usbcore: registered new driver usbserial
Sep 19 05:01:23 localhost kernel: [17180566.528000] drivers/usb/serial/usb-serial.c: USB Serial support registered for generic
Sep 19 05:01:23 localhost kernel: [17180566.528000] usbserial_generic 4-1:1.0: generic converter detected
Sep 19 05:01:23 localhost kernel: [17180566.532000] usb 4-1: generic converter now attached to ttyUSB0
Sep 19 05:01:23 localhost kernel: [17180566.532000] usbserial_generic 4-1:1.1: generic converter detected
Sep 19 05:01:23 localhost kernel: [17180566.532000] usb 4-1: generic converter now attached to ttyUSB1
Sep 19 05:01:23 localhost kernel: [17180566.532000] usbcore: registered new driver usbserial_generic
Sep 19 05:01:23 localhost kernel: [17180566.532000] drivers/usb/serial/usb-serial.c: USB Serial Driver core


Now i think i have a problem cause it looks like he is detecting my 4 in 1 card reader and not my u740 card ... just a thought not sure :D
 
Nope - that looks right. Now try the port as /dev/ttyUSB0 :)

raistlin said:
Ok the modprobe gave me

Sep 19 05:01:23 localhost kernel: [17180566.528000] usbcore: registered new driver usbserial
Sep 19 05:01:23 localhost kernel: [17180566.528000] drivers/usb/serial/usb-serial.c: USB Serial support registered for generic
Sep 19 05:01:23 localhost kernel: [17180566.528000] usbserial_generic 4-1:1.0: generic converter detected
Sep 19 05:01:23 localhost kernel: [17180566.532000] usb 4-1: generic converter now attached to ttyUSB0
Sep 19 05:01:23 localhost kernel: [17180566.532000] usbserial_generic 4-1:1.1: generic converter detected
Sep 19 05:01:23 localhost kernel: [17180566.532000] usb 4-1: generic converter now attached to ttyUSB1
Sep 19 05:01:23 localhost kernel: [17180566.532000] usbcore: registered new driver usbserial_generic
Sep 19 05:01:23 localhost kernel: [17180566.532000] drivers/usb/serial/usb-serial.c: USB Serial Driver core


Now i think i have a problem cause it looks like he is detecting my 4 in 1 card reader and not my u740 card ... just a thought not sure :D
Click to expand...
 
now

cat /proc/bus/usb/devices

gives me

Code: 
T:  Bus=05 Lev=00 Prnt=00 Port=00 Cnt=00 Dev#=  1 Spd=12  MxCh= 2
B:  Alloc=  0/900 us ( 0%), #Int=  0, #Iso=  0
D:  Ver= 1.10 Cls=09(hub  ) Sub=00 Prot=00 MxPS=64 #Cfgs=  1
P:  Vendor=0000 ProdID=0000 Rev= 2.06
S:  Manufacturer=Linux 2.6.15-27-386 ohci_hcd
S:  Product=OHCI Host Controller
S:  SerialNumber=0000:07:00.1
C:* #Ifs= 1 Cfg#= 1 Atr=c0 MxPwr=  0mA
I:  If#= 0 Alt= 0 #EPs= 1 Cls=09(hub  ) Sub=00 Prot=00 Driver=hub
E:  Ad=81(I) Atr=03(Int.) MxPS=   2 Ivl=255ms

T:  Bus=04 Lev=00 Prnt=00 Port=00 Cnt=00 Dev#=  1 Spd=12  MxCh= 3
B:  Alloc=  0/900 us ( 0%), #Int=  0, #Iso=  0
D:  Ver= 1.10 Cls=09(hub  ) Sub=00 Prot=00 MxPS=64 #Cfgs=  1
P:  Vendor=0000 ProdID=0000 Rev= 2.06
S:  Manufacturer=Linux 2.6.15-27-386 ohci_hcd
S:  Product=OHCI Host Controller
S:  SerialNumber=0000:07:00.0
C:* #Ifs= 1 Cfg#= 1 Atr=c0 MxPwr=  0mA
I:  If#= 0 Alt= 0 #EPs= 1 Cls=09(hub  ) Sub=00 Prot=00 Driver=hub
E:  Ad=81(I) Atr=03(Int.) MxPS=   2 Ivl=255ms

T:  Bus=04 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#=  6 Spd=12  MxCh= 0
D:  Ver= 1.10 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs=  1
P:  Vendor=1410 ProdID=1410 Rev= 0.00
S:  Manufacturer=Novatel Wireless
S:  Product=Novatel Wireless HSDPA Modem
C:* #Ifs= 2 Cfg#= 1 Atr=a0 MxPwr=500mA
I:  If#= 0 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=usbserial_generic
E:  Ad=81(I) Atr=03(Int.) MxPS=  16 Ivl=128ms
E:  Ad=82(I) Atr=02(Bulk) MxPS=  64 Ivl=0ms
E:  Ad=02(O) Atr=02(Bulk) MxPS=  64 Ivl=0ms
I:  If#= 1 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=usbserial_generic
E:  Ad=84(I) Atr=02(Bulk) MxPS=  64 Ivl=0ms
E:  Ad=04(O) Atr=02(Bulk) MxPS=  64 Ivl=0ms

T:  Bus=03 Lev=00 Prnt=00 Port=00 Cnt=00 Dev#=  1 Spd=480 MxCh= 8
B:  Alloc=  0/800 us ( 0%), #Int=  0, #Iso=  0
D:  Ver= 2.00 Cls=09(hub  ) Sub=00 Prot=01 MxPS=64 #Cfgs=  1
P:  Vendor=0000 ProdID=0000 Rev= 2.06
S:  Manufacturer=Linux 2.6.15-27-386 ehci_hcd
S:  Product=EHCI Host Controller
S:  SerialNumber=0000:00:13.2
C:* #Ifs= 1 Cfg#= 1 Atr=c0 MxPwr=  0mA
I:  If#= 0 Alt= 0 #EPs= 1 Cls=09(hub  ) Sub=00 Prot=00 Driver=hub
E:  Ad=81(I) Atr=03(Int.) MxPS=   2 Ivl=256ms

T:  Bus=02 Lev=00 Prnt=00 Port=00 Cnt=00 Dev#=  1 Spd=12  MxCh= 4
B:  Alloc=  0/900 us ( 0%), #Int=  0, #Iso=  0
D:  Ver= 1.10 Cls=09(hub  ) Sub=00 Prot=00 MxPS=64 #Cfgs=  1
P:  Vendor=0000 ProdID=0000 Rev= 2.06
S:  Manufacturer=Linux 2.6.15-27-386 ohci_hcd
S:  Product=OHCI Host Controller
S:  SerialNumber=0000:00:13.1
C:* #Ifs= 1 Cfg#= 1 Atr=c0 MxPwr=  0mA
I:  If#= 0 Alt= 0 #EPs= 1 Cls=09(hub  ) Sub=00 Prot=00 Driver=hub
E:  Ad=81(I) Atr=03(Int.) MxPS=   2 Ivl=255ms

T:  Bus=01 Lev=00 Prnt=00 Port=00 Cnt=00 Dev#=  1 Spd=12  MxCh= 4
B:  Alloc= 14/900 us ( 2%), #Int=  1, #Iso=  0
D:  Ver= 1.10 Cls=09(hub  ) Sub=00 Prot=00 MxPS=64 #Cfgs=  1
P:  Vendor=0000 ProdID=0000 Rev= 2.06
S:  Manufacturer=Linux 2.6.15-27-386 ohci_hcd
S:  Product=OHCI Host Controller
S:  SerialNumber=0000:00:13.0
C:* #Ifs= 1 Cfg#= 1 Atr=c0 MxPwr=  0mA
I:  If#= 0 Alt= 0 #EPs= 1 Cls=09(hub  ) Sub=00 Prot=00 Driver=hub
E:  Ad=81(I) Atr=03(Int.) MxPS=   2 Ivl=255ms

T:  Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#=  3 Spd=1.5 MxCh= 0
D:  Ver= 1.10 Cls=00(>ifc ) Sub=00 Prot=00 MxPS= 8 #Cfgs=  1
P:  Vendor=1267 ProdID=0210 Rev= 0.01
S:  Product=PS/2+USB Mouse
C:* #Ifs= 1 Cfg#= 1 Atr=a0 MxPwr=100mA
I:  If#= 1 Alt= 0 #EPs= 1 Cls=03(HID  ) Sub=01 Prot=02 Driver=usbhid
E:  Ad=81(I) Atr=03(Int.) MxPS=   8 Ivl=10ms
 
Another thing is when i try to use ttyS1 it gives me this message in the other console when i run the dial

ttyS1: LSR safety check engaged!
 
It won't be on ttyS1

T: Bus=04 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 6 Spd=12 MxCh= 0
D: Ver= 1.10 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1
P: Vendor=1410 ProdID=1410 Rev= 0.00
S: Manufacturer=Novatel Wireless
S: Product=Novatel Wireless HSDPA Modem
C:* #Ifs= 2 Cfg#= 1 Atr=a0 MxPwr=500mA
I: If#= 0 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=usbserial_generic
E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=128ms
E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms
E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms
I: If#= 1 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=usbserial_generic
E: Ad=84(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms
E: Ad=04(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms

It's a usb device....

I will check and let you know.

raistlin said:
Another thing is when i try to use ttyS1 it gives me this message in the other console when i run the dial

ttyS1: LSR safety check engaged!
Click to expand...
 
Hey raistlin,

I have tried it on my notebook - my card was product id 1400 and after the modprobe it came up as /dev/ttyUSB0 - I connected first time. Does the card work under Windows ?

Laterz !

raistlin said:
Another thing is when i try to use ttyS1 it gives me this message in the other console when i run the dial

ttyS1: LSR safety check engaged!
Click to expand...
 
i am new to linux and umts need help

i live in germany and would like to connect with a novatel u740 to the vodafone umts network, i hope thats somehow similar to vodacom?

i first checked the hw, yast gave me the following hw listing for the u740:

0: udi = '/org/freedesktop/Hal/devices/usb_device_1410_1400_noserial_if1_serial_usb_1'
info.udi = '/org/freedesktop/Hal/devices/usb_device_1410_1400_noserial_if1_serial_usb_1'
info.callouts.remove = { 'hal-resmgr' }
info.callouts.add = { 'hal-resmgr' }
resmgr.class = 'modem'
resmgr.device = '/dev/ttyUSB1'
linux.device_file = '/dev/ttyUSB1'
linux.subsystem = 'tty'
linux.hotplug_type = 2 (0x2)
info.product = 'Novatel Wireless HSDPA Modem'
serial.type = 'usb'
serial.port = 1 (0x1)
serial.device = '/dev/ttyUSB1'
serial.physical_device = '/org/freedesktop/Hal/devices/usb_device_1410_1400_noserial_if1'
info.capabilities = { 'serial' }
info.category = 'serial'
info.parent = '/org/freedesktop/Hal/devices/usb_device_1410_1400_noserial_if1'
linux.sysfs_path = '/sys/class/tty/ttyUSB1'

1: udi = '/org/freedesktop/Hal/devices/usb_device_1410_1400_noserial_if0_serial_usb_0'
info.udi = '/org/freedesktop/Hal/devices/usb_device_1410_1400_noserial_if0_serial_usb_0'
info.callouts.remove = { 'hal-resmgr' }
info.callouts.add = { 'hal-resmgr' }
resmgr.class = 'modem'
resmgr.device = '/dev/ttyUSB0'
linux.device_file = '/dev/ttyUSB0'
linux.subsystem = 'tty'
linux.hotplug_type = 2 (0x2)
info.product = 'Novatel Wireless HSDPA Modem'
serial.type = 'usb'
serial.port = 0 (0x0)
serial.device = '/dev/ttyUSB0'
serial.physical_device = '/org/freedesktop/Hal/devices/usb_device_1410_1400_noserial_if0'
info.capabilities = { 'serial' }
info.category = 'serial'
info.parent = '/org/freedesktop/Hal/devices/usb_device_1410_1400_noserial_if0'
linux.sysfs_path = '/sys/class/tty/ttyUSB0'

2: udi = '/org/freedesktop/Hal/devices/usb_device_1410_1400_noserial_usbraw'
info.udi = '/org/freedesktop/Hal/devices/usb_device_1410_1400_noserial_usbraw'
linux.device_file = '/dev/bus/usb/006/002'
linux.subsystem = 'usb_device'
linux.hotplug_type = 2 (0x2)
usbraw.device = '/dev/bus/usb/006/002'
info.product = 'USB Raw Device Access'
info.capabilities = { 'usbraw' }
info.category = 'usbraw'
info.parent = '/org/freedesktop/Hal/devices/usb_device_1410_1400_noserial'
linux.sysfs_path = '/sys/class/usb_device/usbdev6.2'

3: udi = '/org/freedesktop/Hal/devices/usb_device_1410_1400_noserial_if0'
info.linux.driver = 'generic'
info.udi = '/org/freedesktop/Hal/devices/usb_device_1410_1400_noserial_if0'
linux.subsystem = 'usb'
linux.hotplug_type = 1 (0x1)
info.product = 'USB Vendor Specific Interface'
usb.interface.protocol = 255 (0xff)
usb.interface.subclass = 255 (0xff)
usb.interface.class = 255 (0xff)
usb.interface.number = 0 (0x0)
usb.linux.sysfs_path = '/sys/devices/pci0000:00/0000:00:1e.0/0000:04:00.0/0000:05:00.0/usb6/6-1/6-1:1.0'
usb.configuration_value = 1 (0x1)
usb.num_configurations = 1 (0x1)
usb.num_interfaces = 2 (0x2)
usb.device_class = 0 (0x0)
usb.device_subclass = 0 (0x0)
usb.device_protocol = 0 (0x0)
usb.vendor_id = 5136 (0x1410)
usb.product_id = 5120 (0x1400)
usb.vendor = 'Novatel Wireless'
usb.product = 'USB Vendor Specific Interface'
usb.device_revision_bcd = 0 (0x0)
usb.max_power = 500 (0x1f4)
usb.num_ports = 0 (0x0)
usb.linux.device_number = 2 (0x2)
usb.speed_bcd = 4608 (0x1200)
usb.version_bcd = 272 (0x110)
usb.is_self_powered = false
usb.can_wake_up = true
usb.bus_number = 6 (0x6)
info.bus = 'usb'
info.parent = '/org/freedesktop/Hal/devices/usb_device_1410_1400_noserial'
linux.sysfs_path_device = '/sys/devices/pci0000:00/0000:00:1e.0/0000:04:00.0/0000:05:00.0/usb6/6-1/6-1:1.0'
linux.sysfs_path = '/sys/devices/pci0000:00/0000:00:1e.0/0000:04:00.0/0000:05:00.0/usb6/6-1/6-1:1.0'

4: udi = '/org/freedesktop/Hal/devices/usb_device_1410_1400_noserial_if1'
info.linux.driver = 'generic'
info.udi = '/org/freedesktop/Hal/devices/usb_device_1410_1400_noserial_if1'
linux.subsystem = 'usb'
linux.hotplug_type = 1 (0x1)
info.product = 'USB Vendor Specific Interface'
usb.interface.protocol = 255 (0xff)
usb.interface.subclass = 255 (0xff)
usb.interface.class = 255 (0xff)
usb.interface.number = 1 (0x1)
usb.linux.sysfs_path = '/sys/devices/pci0000:00/0000:00:1e.0/0000:04:00.0/0000:05:00.0/usb6/6-1/6-1:1.1'
usb.configuration_value = 1 (0x1)
usb.num_configurations = 1 (0x1)
usb.num_interfaces = 2 (0x2)
usb.device_class = 0 (0x0)
usb.device_subclass = 0 (0x0)
usb.device_protocol = 0 (0x0)
usb.vendor_id = 5136 (0x1410)
usb.product_id = 5120 (0x1400)
usb.vendor = 'Novatel Wireless'
usb.product = 'USB Vendor Specific Interface'
usb.device_revision_bcd = 0 (0x0)
usb.max_power = 500 (0x1f4)
usb.num_ports = 0 (0x0)
usb.linux.device_number = 2 (0x2)
usb.speed_bcd = 4608 (0x1200)
usb.version_bcd = 272 (0x110)
usb.is_self_powered = false
usb.can_wake_up = true
usb.bus_number = 6 (0x6)
info.bus = 'usb'
info.parent = '/org/freedesktop/Hal/devices/usb_device_1410_1400_noserial'
linux.sysfs_path_device = '/sys/devices/pci0000:00/0000:00:1e.0/0000:04:00.0/0000:05:00.0/usb6/6-1/6-1:1.1'
linux.sysfs_path = '/sys/devices/pci0000:00/0000:00:1e.0/0000:04:00.0/0000:05:00.0/usb6/6-1/6-1:1.1'

5: udi = '/org/freedesktop/Hal/devices/usb_device_1410_1400_noserial'
info.udi = '/org/freedesktop/Hal/devices/usb_device_1410_1400_noserial'
linux.subsystem = 'usb'
linux.hotplug_type = 1 (0x1)
usb_device.bus_number = 6 (0x6)
usb_device.can_wake_up = true
usb_device.is_self_powered = false
usb_device.version_bcd = 272 (0x110)
usb_device.speed_bcd = 4608 (0x1200)
usb_device.linux.device_number = 2 (0x2)
usb_device.num_ports = 0 (0x0)
usb_device.max_power = 500 (0x1f4)
usb_device.device_revision_bcd = 0 (0x0)
info.product = 'Novatel Wireless HSDPA Modem'
usb_device.product = 'Novatel Wireless HSDPA Modem'
info.vendor = 'Novatel Wireless'
usb_device.vendor = 'Novatel Wireless'
usb_device.product_id = 5120 (0x1400)
usb_device.vendor_id = 5136 (0x1410)
usb_device.device_protocol = 0 (0x0)
usb_device.device_subclass = 0 (0x0)
usb_device.device_class = 0 (0x0)
usb_device.num_interfaces = 2 (0x2)
usb_device.num_configurations = 1 (0x1)
usb_device.configuration_value = 1 (0x1)
usb_device.linux.sysfs_path = '/sys/devices/pci0000:00/0000:00:1e.0/0000:04:00.0/0000:05:00.0/usb6/6-1'
info.linux.driver = 'usb'
info.bus = 'usb_device'
info.parent = '/org/freedesktop/Hal/devices/usb_device_0_0_0000_05_00_0'
linux.sysfs_path_device = '/sys/devices/pci0000:00/0000:00:1e.0/0000:04:00.0/0000:05:00.0/usb6/6-1'
linux.sysfs_path = '/sys/devices/pci0000:00/0000:00:1e.0/0000:04:00.0/0000:05:00.0/usb6/6-1'


reading through this thread i am posting too i was modifying wvdial.conf to:

[Dialer hsdpa]

Modem = /dev/ttyUSB0
Baud = 460800
Init2 = ATZ
Init3 = ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0
ISDN = 0
Modem Type = Analog Modem


while testing it i got this response from my system:

linux-89sr:/etc # wvdial hsdpa
--> WvDial: Internet dialer version 1.54.0
--> Cannot get information for serial port.
--> Initializing modem.
--> Sending: ATZ
ATZ
OK
--> Sending: ATZ
ATZ
OK
--> Sending: ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0
ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0
OK
--> Modem initialized.
--> Configuration does not specify a valid phone number.
--> Configuration does not specify a valid login name.
linux-89sr:/etc #


the linux i use is use is suse 10.1

now i stuck and wish for someone nice taking me through that dark forrest, :)

Peter
 
Last edited:
I have an option nozomi, plugged into a cardbus to pci adapter card in my desktop machine. having done everything this tutorial says, I'm still sitting without an internet connection. any ideas pls. ubuntu dapper drake. when i do tail -f /var/log/messages and eject and reinsert the card, all I get is "cardbus card ejected" and "cardbus card inserted" yay.
 
Hey peter,

Add the following to your /etc/wvdial.conf :

[Dialer Defaults]

Phone = *99***1#
Username = username
Password = password
Stupid Mode = 1
Dial Command = ATDT

And away you go !

Laterz !

peter.wilhelm said:
i live in germany and would like to connect with a novatel u740 to the vodafone umts network, i hope thats somehow similar to vodacom?

i first checked the hw, yast gave me the following hw listing for the u740:

0: udi = '/org/freedesktop/Hal/devices/usb_device_1410_1400_noserial_if1_serial_usb_1'
info.udi = '/org/freedesktop/Hal/devices/usb_device_1410_1400_noserial_if1_serial_usb_1'
info.callouts.remove = { 'hal-resmgr' }
info.callouts.add = { 'hal-resmgr' }
resmgr.class = 'modem'
resmgr.device = '/dev/ttyUSB1'
linux.device_file = '/dev/ttyUSB1'
linux.subsystem = 'tty'
linux.hotplug_type = 2 (0x2)
info.product = 'Novatel Wireless HSDPA Modem'
serial.type = 'usb'
serial.port = 1 (0x1)
serial.device = '/dev/ttyUSB1'
serial.physical_device = '/org/freedesktop/Hal/devices/usb_device_1410_1400_noserial_if1'
info.capabilities = { 'serial' }
info.category = 'serial'
info.parent = '/org/freedesktop/Hal/devices/usb_device_1410_1400_noserial_if1'
linux.sysfs_path = '/sys/class/tty/ttyUSB1'

1: udi = '/org/freedesktop/Hal/devices/usb_device_1410_1400_noserial_if0_serial_usb_0'
info.udi = '/org/freedesktop/Hal/devices/usb_device_1410_1400_noserial_if0_serial_usb_0'
info.callouts.remove = { 'hal-resmgr' }
info.callouts.add = { 'hal-resmgr' }
resmgr.class = 'modem'
resmgr.device = '/dev/ttyUSB0'
linux.device_file = '/dev/ttyUSB0'
linux.subsystem = 'tty'
linux.hotplug_type = 2 (0x2)
info.product = 'Novatel Wireless HSDPA Modem'
serial.type = 'usb'
serial.port = 0 (0x0)
serial.device = '/dev/ttyUSB0'
serial.physical_device = '/org/freedesktop/Hal/devices/usb_device_1410_1400_noserial_if0'
info.capabilities = { 'serial' }
info.category = 'serial'
info.parent = '/org/freedesktop/Hal/devices/usb_device_1410_1400_noserial_if0'
linux.sysfs_path = '/sys/class/tty/ttyUSB0'

2: udi = '/org/freedesktop/Hal/devices/usb_device_1410_1400_noserial_usbraw'
info.udi = '/org/freedesktop/Hal/devices/usb_device_1410_1400_noserial_usbraw'
linux.device_file = '/dev/bus/usb/006/002'
linux.subsystem = 'usb_device'
linux.hotplug_type = 2 (0x2)
usbraw.device = '/dev/bus/usb/006/002'
info.product = 'USB Raw Device Access'
info.capabilities = { 'usbraw' }
info.category = 'usbraw'
info.parent = '/org/freedesktop/Hal/devices/usb_device_1410_1400_noserial'
linux.sysfs_path = '/sys/class/usb_device/usbdev6.2'

3: udi = '/org/freedesktop/Hal/devices/usb_device_1410_1400_noserial_if0'
info.linux.driver = 'generic'
info.udi = '/org/freedesktop/Hal/devices/usb_device_1410_1400_noserial_if0'
linux.subsystem = 'usb'
linux.hotplug_type = 1 (0x1)
info.product = 'USB Vendor Specific Interface'
usb.interface.protocol = 255 (0xff)
usb.interface.subclass = 255 (0xff)
usb.interface.class = 255 (0xff)
usb.interface.number = 0 (0x0)
usb.linux.sysfs_path = '/sys/devices/pci0000:00/0000:00:1e.0/0000:04:00.0/0000:05:00.0/usb6/6-1/6-1:1.0'
usb.configuration_value = 1 (0x1)
usb.num_configurations = 1 (0x1)
usb.num_interfaces = 2 (0x2)
usb.device_class = 0 (0x0)
usb.device_subclass = 0 (0x0)
usb.device_protocol = 0 (0x0)
usb.vendor_id = 5136 (0x1410)
usb.product_id = 5120 (0x1400)
usb.vendor = 'Novatel Wireless'
usb.product = 'USB Vendor Specific Interface'
usb.device_revision_bcd = 0 (0x0)
usb.max_power = 500 (0x1f4)
usb.num_ports = 0 (0x0)
usb.linux.device_number = 2 (0x2)
usb.speed_bcd = 4608 (0x1200)
usb.version_bcd = 272 (0x110)
usb.is_self_powered = false
usb.can_wake_up = true
usb.bus_number = 6 (0x6)
info.bus = 'usb'
info.parent = '/org/freedesktop/Hal/devices/usb_device_1410_1400_noserial'
linux.sysfs_path_device = '/sys/devices/pci0000:00/0000:00:1e.0/0000:04:00.0/0000:05:00.0/usb6/6-1/6-1:1.0'
linux.sysfs_path = '/sys/devices/pci0000:00/0000:00:1e.0/0000:04:00.0/0000:05:00.0/usb6/6-1/6-1:1.0'

4: udi = '/org/freedesktop/Hal/devices/usb_device_1410_1400_noserial_if1'
info.linux.driver = 'generic'
info.udi = '/org/freedesktop/Hal/devices/usb_device_1410_1400_noserial_if1'
linux.subsystem = 'usb'
linux.hotplug_type = 1 (0x1)
info.product = 'USB Vendor Specific Interface'
usb.interface.protocol = 255 (0xff)
usb.interface.subclass = 255 (0xff)
usb.interface.class = 255 (0xff)
usb.interface.number = 1 (0x1)
usb.linux.sysfs_path = '/sys/devices/pci0000:00/0000:00:1e.0/0000:04:00.0/0000:05:00.0/usb6/6-1/6-1:1.1'
usb.configuration_value = 1 (0x1)
usb.num_configurations = 1 (0x1)
usb.num_interfaces = 2 (0x2)
usb.device_class = 0 (0x0)
usb.device_subclass = 0 (0x0)
usb.device_protocol = 0 (0x0)
usb.vendor_id = 5136 (0x1410)
usb.product_id = 5120 (0x1400)
usb.vendor = 'Novatel Wireless'
usb.product = 'USB Vendor Specific Interface'
usb.device_revision_bcd = 0 (0x0)
usb.max_power = 500 (0x1f4)
usb.num_ports = 0 (0x0)
usb.linux.device_number = 2 (0x2)
usb.speed_bcd = 4608 (0x1200)
usb.version_bcd = 272 (0x110)
usb.is_self_powered = false
usb.can_wake_up = true
usb.bus_number = 6 (0x6)
info.bus = 'usb'
info.parent = '/org/freedesktop/Hal/devices/usb_device_1410_1400_noserial'
linux.sysfs_path_device = '/sys/devices/pci0000:00/0000:00:1e.0/0000:04:00.0/0000:05:00.0/usb6/6-1/6-1:1.1'
linux.sysfs_path = '/sys/devices/pci0000:00/0000:00:1e.0/0000:04:00.0/0000:05:00.0/usb6/6-1/6-1:1.1'

5: udi = '/org/freedesktop/Hal/devices/usb_device_1410_1400_noserial'
info.udi = '/org/freedesktop/Hal/devices/usb_device_1410_1400_noserial'
linux.subsystem = 'usb'
linux.hotplug_type = 1 (0x1)
usb_device.bus_number = 6 (0x6)
usb_device.can_wake_up = true
usb_device.is_self_powered = false
usb_device.version_bcd = 272 (0x110)
usb_device.speed_bcd = 4608 (0x1200)
usb_device.linux.device_number = 2 (0x2)
usb_device.num_ports = 0 (0x0)
usb_device.max_power = 500 (0x1f4)
usb_device.device_revision_bcd = 0 (0x0)
info.product = 'Novatel Wireless HSDPA Modem'
usb_device.product = 'Novatel Wireless HSDPA Modem'
info.vendor = 'Novatel Wireless'
usb_device.vendor = 'Novatel Wireless'
usb_device.product_id = 5120 (0x1400)
usb_device.vendor_id = 5136 (0x1410)
usb_device.device_protocol = 0 (0x0)
usb_device.device_subclass = 0 (0x0)
usb_device.device_class = 0 (0x0)
usb_device.num_interfaces = 2 (0x2)
usb_device.num_configurations = 1 (0x1)
usb_device.configuration_value = 1 (0x1)
usb_device.linux.sysfs_path = '/sys/devices/pci0000:00/0000:00:1e.0/0000:04:00.0/0000:05:00.0/usb6/6-1'
info.linux.driver = 'usb'
info.bus = 'usb_device'
info.parent = '/org/freedesktop/Hal/devices/usb_device_0_0_0000_05_00_0'
linux.sysfs_path_device = '/sys/devices/pci0000:00/0000:00:1e.0/0000:04:00.0/0000:05:00.0/usb6/6-1'
linux.sysfs_path = '/sys/devices/pci0000:00/0000:00:1e.0/0000:04:00.0/0000:05:00.0/usb6/6-1'


reading through this thread i am posting too i was modifying wvdial.conf to:

[Dialer hsdpa]

Modem = /dev/ttyUSB0
Baud = 460800
Init2 = ATZ
Init3 = ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0
ISDN = 0
Modem Type = Analog Modem


while testing it i got this response from my system:

linux-89sr:/etc # wvdial hsdpa
--> WvDial: Internet dialer version 1.54.0
--> Cannot get information for serial port.
--> Initializing modem.
--> Sending: ATZ
ATZ
OK
--> Sending: ATZ
ATZ
OK
--> Sending: ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0
ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0
OK
--> Modem initialized.
--> Configuration does not specify a valid phone number.
--> Configuration does not specify a valid login name.
linux-89sr:/etc #


the linux i use is use is suse 10.1

now i stuck and wish for someone nice taking me through that dark forrest, :)

Peter
Click to expand...
 
Did you compile the driver ?

Laterz !

sevenworth said:
I have an option nozomi, plugged into a cardbus to pci adapter card in my desktop machine. having done everything this tutorial says, I'm still sitting without an internet connection. any ideas pls. ubuntu dapper drake. when i do tail -f /var/log/messages and eject and reinsert the card, all I get is "cardbus card ejected" and "cardbus card inserted" yay.
Click to expand...
 
Tazz_Tux,

first of all thank you, that did get me quit e bit further:

linux-89sr:/etc # wvdial hsdpa
--> WvDial: Internet dialer version 1.54.0
--> Cannot get information for serial port.
--> Initializing modem.
--> Sending: ATZ
ATZ
OK
--> Sending: ATZ
ATZ
OK
--> Sending: ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0
ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0
OK
--> Modem initialized.
--> Sending: ATDT*99***1#
--> Waiting for carrier.
ATDT*99***1#
CONNECT HSDPA 1.8
--> Carrier detected. Starting PPP immediately.
--> Starting pppd at Tue Sep 26 22:52:07 2006
--> pid of pppd: 16318
--> Using interface ppp0
--> pppd: dem
--> pppd: dem
--> pppd: dem
--> pppd: dem
--> pppd: dem
--> local IP address 10.227.43.237
--> pppd: dem
--> remote IP address 10.64.64.64
--> pppd: dem
--> primary DNS address 139.7.30.125
--> pppd: dem
--> secondary DNS address 139.7.30.126
--> pppd: dem
--> Script /etc/ppp/ip-up run successful
--> Default route Ok.
--> warning, can't find address for `www.suse.de`
--> warning, address lookup does not work
--> Nameserver (DNS) failure, the connection may not work.
--> Connected... Press Ctrl-C to disconnect

the pcmai card also got bright blue, but still i can not get connected to the internet with my little firefox browser and had to stop the UMTS service before beeing able using my ethernet/dsl routing.

i checked for /dev/ttyUSB0 and could not found that entry in /dev, and tried to create with MAKEDEV, but that command is not recognized by my system (suse 10.1)

it feels like i am almost there, but i still need a little more help before i can enter the UMTS heaven :)

Peter
 
Last edited:
Status
Not open for further replies.
Back
Top
Sign up to the MyBroadband newsletter
X