Anyone run 24v Ubiquiti devices connected directly to 2x 12v batteries? My Mikrotik router, switch, and ONT is connected to a single 12v 33Ah gel battery that gets charged via a 100w panel. I'm thinking of adding a second battery and another panel, so I can power my two tough switches at the other end of the house on 24v, however, I assume the voltage while charging will be over 27v, and the input voltage for the switches are 22-24v 2.5A...
What will be the best way to regulate the voltage from the batteries to 24v? I'm sure I could just wire in a fuse, resistor, and a zener diode to do the job?
Maybe, but if that's the case and it's charging and discharging at the same time then the battery isn't doing anything so how does that shorten its life?
Maybe, but if that's the case and it's charging and discharging at the same time then the battery isn't doing anything so how does that shorten its life?
It draws power from the battery while charging it? Won't that generate internal heat and cause unnecessary movement of ions which will reduce longetivity? So during this time the unit should be mains powered but instead powers battery which powers your kit, while mains AC is on.
I am pretty sure that the Geewiz description is because of the experience that I had. I bought the unit from Geewiz, tried to use it, followed all the instructions, but it kept inexplicably dying in the middle of the night. Eventually I setup a camera to catch when it died.
Geewiz were really good; they asked questions which I answered, reached out to the supplier, and the supplier provided feedback that it couldn't work as a UPS. They then advised that they had updated the site.
South Africa's leading online store. Fast, reliable delivery to your door. Many ways to pay. Shop anything you can imagine: TVs, laptops, cellphones, kitchen appliances, toys, books, beauty & more. Shop the mobile app anytime, anywhere.
www.takealot.com
Should keep my entire network and alarm CCTV running for 3-4 hours. Going the easy route, by just putting the plug into it. Don't care about the other ports. Apparently works like a UPS, so it powers everything downroute while it itself is being charge.
Let's hope it works.
Edit : now having caught up with the thread , hoping when it is being charged and providing power to downstream devices , that it is bypassing the batteries. Wonder how one would check that.
South Africa's leading online store. Fast, reliable delivery to your door. Many ways to pay. Shop anything you can imagine: TVs, laptops, cellphones, kitchen appliances, toys, books, beauty & more. Shop the mobile app anytime, anywhere.
www.takealot.com
Should keep my entire network and alarm CCTV running for 3-4 hours. Going the easy route, by just putting the plug into it. Don't care about the other ports. Apparently works like a UPS, so it powers everything downroute while it itself is being charge.
Let's hope it works.
Edit : now having caught up with the thread , hoping when it is being charged and providing power to downstream devices , that it is bypassing the batteries. Wonder how one would check that.
It draws power from the battery while charging it? Won't that generate internal heat and cause unnecessary movement of ions which will reduce longetivity? So during this time the unit should be mains powered but instead powers battery which powers your kit, while mains AC is on.
Maybe, but if that's the case and it's charging and discharging at the same time then the battery isn't doing anything so how does that shorten its life?
This didn't make any sense. It is not possible for current to be following to and from the battery at the same time. It can be likened to a hosepipe. Water can't be following in both directions at the same time.
Either a power source is feeding the battery and the load at the same time, or the battery is feeding the load if there is no other power source.
It draws power from the battery while charging it? Won't that generate internal heat and cause unnecessary movement of ions which will reduce longetivity? So during this time the unit should be mains powered but instead powers battery which powers your kit, while mains AC is on.
In that case batteries in online UPS's must get smashed because they run off the battery all the time or maybe they don't? I would think as long as the charge current is more than the draw current then the battery will stay full. I'm just speculating as I'm no expert, just thinking out loud.
I was using the Huawei B315 with Huawei battery - that thing lasts more than 4 hours.
Just got fibre - the Huawei B315 has the same power connection as the Mikrotik Hap AC2 they supplied, but the Frogfoot ONT takes a different power input.
Which battery similar to the Huawei would work on the ONT?
I was using the Huawei B315 with Huawei battery - that thing lasts more than 4 hours.
Just got fibre - the Huawei B315 has the same power connection as the Mikrotik Hap AC2 they supplied, but the Frogfoot ONT takes a different power input.
Which battery similar to the Huawei would work on the ONT?
This didn't make any sense. It is not possible for current to be following to and from the battery at the same time. It can be likened to a hosepipe. Water can't be following in both directions at the same time.
Either a power source is feeding the battery and the load at the same time, or the battery is feeding the load if there is no other power source.
In that case batteries in online UPS's must get smashed because they run off the battery all the time or maybe they don't? I would think as long as the charge current is more than the draw current then the battery will stay full. I'm just speculating as I'm no expert, just thinking out loud.